Solid Waste Pyrolysis Solutions

With the rapid economic development and accelerated urbanization, solid waste management has become one of the major environmental challenges worldwide. Effective management and treatment of solid waste are not only crucial for sustainable environmental development but also directly impact the quality of human life. As an integral part of waste-to-energy solutions, solid waste pyrolysis solutions are experiencing unprecedented development opportunities. The goals of solid waste management are to ensure harmlessness, reduction, and resource utilization while striving to promote the industry towards diversification and intelligent development.

AGICO is committed to providing you with comprehensive solutions for solid waste pyrolysis and offering a one-stop service with pyrolysis plants for sale.

AGICO Hot-sale Solid Waste Pyrolysis Plants

Waste Tyre Pyrolysis Plant

The pyrolysis of waste tires is conducted in a sealed pyrolysis reactor, where the tires are heated to around 200°C. The rubber in the tires decomposes into monomers and then polymerizes into various olefins. The oil yield from tire pyrolysis is approximately 50%-60%. The final products mainly include pyrolysis oil, combustible gases, carbon black, and steel wire. Through the tire pyrolysis process, waste tires can be recycled into reusable energy without causing secondary environmental pollution. AGICO’s waste tire pyrolysis plants are equipped with flue gas purification systems, exhaust gas purification systems, deodorization systems, and water circulation systems, ensuring no pollution to air and water bodies.

Waste Plastic Pyrolysis Plant

AGICO’s waste plastic pyrolysis plant is a comprehensive, systematic production line that uses advanced pyrolysis technology to convert waste plastic into energy products such as pyrolysis oil, carbon black, and fuel gas, all of which can be reused as resources.

Waste Rubber Pyrolysis Plant

There are various types of waste rubber, primarily including vehicle tires such as car tires, tractor tires, and bicycle inner and outer tubes. Additionally, it includes soft pipelines used for transporting liquids and gases, rubber belts, rubber flooring, rubber shoes, and rubber soles. The products obtained from rubber pyrolysis are pyrolysis oil, carbon black, steel wire, and synthetic fuel gas. The higher the purity of the rubber, the higher the oil yield.

Oil Sludge Pyrolysis Plant

An oil sludge pyrolysis plant processes petroleum waste (such as oil-containing sludge produced during oil extraction and oilfield waste) through high-temperature pyrolysis to extract usable energy and reduce the volume of waste. The final products of oil sludge pyrolysis typically include pyrolysis oil, recovered sand, and water. Pyrolysis oil and water each constitute about 12.5% of the output, with the remaining 72.5% being sand. These proportions can vary depending on the specific composition of the oil sludge and the pyrolysis conditions.

Biomass Pyrolysis Plant

A biomass pyrolysis plant is a production line that utilizes pyrolysis technology to convert biomass into valuable energy products. By heating biomass raw materials such as crop residues and wood waste in an oxygen-free environment, the pyrolysis process can produce biochar, pyrolysis oil, and pyrolysis gas. The primary applications of a biomass pyrolysis plant include producing renewable energy, reducing greenhouse gas emissions, and improving soil fertility. Biochar, one of the pyrolysis products, can enhance soil structure and increase crop yields, while pyrolysis oil is an important source of bio-based chemicals and fuels. Pyrolysis gas can be directly used or processed as a clean energy source.

Animal Manure Pyrolysis

The integrated pyrolysis treatment equipment for livestock and poultry manure can directly process various types of manure with a moisture content of no more than 90%. Through high-temperature fermentation, the manure is rapidly deodorized, producing energy and solid organic fertilizer, making it an excellent choice for turning waste into wealth.

Thermal Regeneration Of Activated Carbon

The rotary kiln regeneration of activated carbon and the pyrolysis of spent activated carbon can bring significant savings to drinking water purification facilities. By heating spent activated carbon to over 600°C, approximately 90% of the adsorbed materials are volatilized, restoring the adsorption capacity of the activated carbon for reuse.

MSW Pyrolysis Plant

Municipal solid waste (MSW) is a widely used biomass source for producing biofuels. Research indicates that pyrolysis is one of the best processes for handling large volumes of municipal waste. AGICO’s municipal solid waste pyrolysis plant can convert waste into high-calorific-value biofuels. The pyrolysis gas can be used for industrial power generation, and the pyrolysis oil can be further processed into tar and other liquid fuels.

Sewage Sludge Incineration Plant

Applicable Scope: Various types of sludge including municipal sludge, industrial sludge, etc. (with sludge moisture content ranging from 45% to 80%).

This drying and incineration technology is globally advanced and mature, with independent intellectual property rights. It requires low material moisture content for direct disposal without deep filter pressing, achieving a reduction rate of over 90%. Utilizing the internal residual heat of the incineration system, no additional auxiliary fuel is needed. Incineration can produce steam, and the slag can be used for brick-making. The resource utilization is high, and the exhaust gas is ultra-clean, with pollutant emissions far better than international standards.

Hazardous Waste Incineration Plant

Applicable Scope: Capable of treating various types of hazardous waste, including solids, liquids, colloids, and waste gases.

Flexible adoption of different processes based on regional emission requirements ensures that smoke emissions meet and exceed European standards. The processes can handle various hazardous wastes with high chlorine content (15% or higher) and high sulfur content. The residual heat from incineration can be fully utilized to reduce operating costs. The system has long continuous operation time, low maintenance, and an annual operating rate of over 90%.

Medical Waste Incineration Plant

Applicable Scope: Various medical wastes and household garbage.

Flexible adoption of different processes based on regional emission requirements ensures that smoke emissions meet and exceed European standards. Medical waste is handled by a fully automatic feeding system, automatic cleaning of turnover bins, a mature rotary kiln incineration system, and an ultra-low emission exhaust gas purification process. Equipped with multiple advanced technologies, the system has long continuous operation time, low maintenance, and an annual operating rate of over 90%.

Pyrolysis Of E-waste

AGICO offers pyrolysis projects for electronic waste. The casings of electronic waste are mostly made of different plastics, while components such as circuit boards contain valuable metals, making them suitable raw materials for energy conversion through pyrolysis. During the pyrolysis process, the volatile components of e-waste are thermally decomposed. The energy from the pyrolysis gas is used to recover heat or generate electricity. The solid pyrolysis products include valuable metals, which will be further recycled.

Waste Lithium-ion Batteries Pyrolysis Plant

AGICO provides pyrolysis plants for recycling and processing waste lithium batteries. Our primary goal is to maximize the recovery of usable resources, mainly targeting valuable metals such as lithium, cobalt, and nickel, while minimizing environmental impact.

Cathode Active Material Production Line

AGICO offers production lines for lithium battery cathode active materials, focusing primarily on the high-temperature sintering process. The rotary kilns sold by AGICO for roasting lithium battery cathode and anode materials utilize fuel combustion and electric heating, with a maximum sintering temperature of 1300°C. The kiln atmosphere can be selected from Air, O2, or N2.

Co-Processing In Cement Kilns

Cement production is an energy and resource-intensive industry, with high carbon dioxide emission indices during the manufacturing process. Currently, the cement industry is facing overcapacity and fierce competition. Therefore, helping cement enterprises reduce costs and transition to green practices is the trend. The co-processing of solid waste through cement kilns during clinker production has become the preferred choice for most cement companies in their transformation and upgrading efforts.

Request A Quote

Please fill in the required fields carefully and we will contact you immediately to help you get the service you want.